Psion PowerScan M8300 series Manual do Utilizador Página 178
- Página / 216
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
POWERSCAN™ D8330/M8300
166
5.14 CONFIGURATION COPYING COMMANDS
5.14.1 Copy PowerScan D8330 Series
Procedure:
Connect the master (correctly configured reader) and the slave (reader to be
configured) together through two RS-232 serial interface cables and external
power supply. Accessory cables and power supply are available from your Psion
distributor to provide this connection.
RS-232 Cables: CAB471 & CAB472
Power Supply: PG5
Using the slave reader, read the Restore Default barcode and then the RS-232
interface barcode from chapter 4 of this manual or from the Quick Reference
Guide.
With the master reader, read the Configuration Copy barcode below.
Copy Configuration
Ì$+ZZ0$-*Î
The configuration will be copied from the master to the slave reader. The slave
reader signals the end of the procedure with a series of beeps.
NOTE: The master reader can be configured for any interface.
- PowerScan™ 1
- D8330/M8300 1
- Disclaimer 2
- Return to Factory Warranty 3
- What is RoHS? 4
- Technical Support 5
- Product Repairs 5
- Worldwide Offices 5
- CONTENTS 7
- TABLE OF CONTENTS 9
- GENERAL VIEW 11
- 1 INTRODUCTION 13
- 2 INSTALLATION 14
- 2.3 RS-232 CONNECTION 17
- 2.4 USB 17
- 2.5 IBM USB POS 18
- 2.6 WEDGE CONNECTION 19
- 2.8 NETWORK CONNECTIONS 20
- 2.8.2 Network Cabling 21
- 2.8.3 Network Termination 22
- 2.9 POWERSCAN 23
- M8300 BATTERY MAINTENANCE 23
- 2.9.1 Battery Charging 23
- 2.9.2 Replacing PowerScan 23
- M8300 Batteries 23
- 2.10.1 Desktop Mounting 25
- Portable Desktop Use 26
- Fixed Desktop Use 26
- INSTALLATION 27
- 2.10.2 Wall Mounting 28
- Inclined Base Wall-mounting 29
- 3 POWERSCAN 30
- M8300 SYSTEM AND NETWORK 30
- LAYOUTS 30
- 3.1.4 C-BOX Layout 32
- 3.2.1 Host Master Layout 33
- 3.2.2 BC-8060 Master Layout 34
- Example: 35
- 4 CONFIGURATION 36
- 4.2 SETUP PROCEDURES 37
- Ì$+$*oÎ 38
- 4.5 POWERSCAN 39
- Ì$+RN0$-IÎ 40
- Ì$+RX0$-qÎ 40
- Ì$+RN1$-NÎ 41
- 4.5.2 PowerScan 42
- 4.6 POWERSCAN 43
- M8300/STAR-SYSTEM™ SETUP 43
- Ì$+RF4Î 45
- Ì$+RZ2$-ÇÎ 46
- Ì$+RZ1$-~Î 46
- Ì$+CP0$-$Î 47
- Ì$+CM2EC0$->Î 47
- Ì$+CM1$-ÈÎ 47
- Ì$+CM0$-ÃÎ 47
- Ì$+CP6$-BÎ 47
- First Start-Up 50
- RS-232 PARAMETERS 53
- BAUD RATE 54
- DATA BITS 55
- STOP BITS 55
- HANDSHAKING 55
- ACK/NACK PROTOCOL 56
- INTER-CHARACTER DELAY 56
- RX TIMEOUT 57
- SERIAL TRIGGER LOCK 57
- USB PARAMETERS 58
- KEYBOARD NATIONALITY 61
- INTER-CODE DELAY 63
- USB KEYBOARD SPEED 63
- WEDGE PARAMETERS 64
- CAPS LOCK 66
- NUM LOCK 67
- KEYBOARD SETTING 68
- CONTROL CHARACTER EMULATION 69
- PEN EMULATION 70
- OPERATING MODE 71
- MINIMUM OUTPUT PULSE 72
- OVERFLOW 73
- OUTPUT LEVEL 74
- IDLE LEVEL 74
- INTER-BLOCK DELAY 74
- NETWORK PARAMETERS 75
- RS-485 NETWORK 76
- NETWORK BAUD RATE 76
- SLAVE ADDRESS RANGE 77
- NETWORK WARNING MESSAGE 77
- RECEPTION WARNING MESSAGE 77
- MASTER CRADLE HEADER 78
- MASTER CRADLE TERMINATOR 79
- DATA FORMAT 80
- DATA FORMAT 81
- CODE IDENTIFIER 82
- CUSTOM CODE IDENTIFIER 82
- four character header 83
- TERMINATOR 84
- SPECIAL KEYS 85
- FIELD ADJUSTMENT 86
- FIELD ADJUSTMENT CHARACTER 87
- CODE LENGTH TX 87
- CHARACTER REPLACEMENT 88
- First Character Replacement: 89
- Code 39 barcodes 89
- 91
- SLEEP STATE 93
- ENTER SLEEP TIMEOUT 93
- TRIGGER TYPE 95
- TRIGGER SIGNAL 95
- TRIGGER CLICK 95
- TRIGGER-OFF TIMEOUT 96
- FLASH MODE 96
- READS PER CYCLE 96
- SAFETY TIME 97
- BEEPER INTENSITY 97
- BEEPER TONE 98
- BEEPER TYPE 98
- BEEPER LENGTH 98
- GOOD READ SPOT DURATION 99
- AIMING SYSTEM 99
- CRADLE BEEPER INTENSITY 99
- DECODING PARAMETERS 100
- INK SPREAD 101
- OVERFLOW CONTROL 101
- INTERDIGIT CONTROL 101
- DECODING SAFETY 102
- PUZZLE SOLVER™ 102
- CODE SELECTION 103
- Ì#+AUTOWÎ 104
- DISABLE ALL CODE FAMILIES 105
- EAN/UPC FAMILY 106
- WITHOUT ADD ON 106
- WITH ADD ON 2 AND 5 106
- Enter Configuration 107
- Exit and Save 107
- SELECT EAN/UPC PREFIXES 108
- 434/439: 109
- CONVERSION OPTIONS 111
- 2/5 FAMILY 112
- CODE 39 FAMILY 113
- CODE LENGTH (OPTION 113
- CODE 93 115
- CODABAR FAMILY 115
- CODE 11 118
- CODE 16K 119
- CODE 49 119
- GS1 DATABAR™ CODES 120
- ADVANCED FORMATTING 121
- CONCATENATION 122
- 4 Character Fixed Field 134
- 3 Character Fixed Field 135
- RADIO PARAMETERS 140
- RADIO PROTOCOL TIMEOUT 141
- RADIO RX TIMEOUT 141
- POWER-OFF TIMEOUT 142
- TRANSMISSION MODE 142
- SINGLE STORE 144
- BATCH MODE 145
- FIND ME 145
- DISPLAY AND KEYPAD 146
- PARAMETERS 146
- DISPLAY PARAMETERS 147
- DISPLAY-OFF TIMEOUT 148
- DISPLAY MODE 148
- 5 REFERENCES 150
- 5.1.2 ACK/NACK Protocol 151
- 5.1.3 FIFO 152
- 5.1.4 RX Timeout 153
- 5.2 PEN PARAMETERS 153
- 5.2.1 Minimum Output Pulse 153
- 5.2.3 Overflow 154
- 5.2.5 Inter-Block Delay 155
- 5.3 NETWORK PARAMETERS 155
- 5.4 DATA FORMAT 157
- POWERSCAN™ D8330/M8300 160
- REFERENCES 161
- ÌFQ9C2>Î 163
- 5.4.3 Address Stamping 166
- 5.4.4 Address Delimiter 166
- 5.4.5 Time Stamping Format 166
- 5.5 POWER SAVE 167
- 5.5.1 Sleep State 167
- 5.5.2 Enter Sleep Timeout 167
- 5.6 READING PARAMETERS 168
- 5.6.1 Trigger Signal 168
- 5.6.2 Trigger Click 168
- 5.6.3 Trigger-Off Timeout 168
- 5.6.4 Reads per Cycle 168
- 5.6.5 Safety Time 169
- 5.7 DECODING PARAMETERS 169
- 5.7.1 Ink-Spread 169
- 5.7.2 Overflow Control 169
- 5.7.3 Interdigit Control 170
- 5.8 ADVANCED FORMATTING 170
- 5.8.1 Match Conditions 170
- 5.9.2 Radio RX Timeout 171
- 5.9.3 Power-Off Timeout 171
- 5.9.4 Transmission Mode 172
- 5.9.6 Single Store 173
- 5.9.7 Batch Mode 173
- 5.9.8 Find Me (PowerScan 174
- M8300 only) 174
- 5.10.1 Display Mode 175
- Ì$+$0ÂÎ 177
- Ì$+$1$Î 177
- Ì#+CODEÂÎ 177
- Ì$+ZZ0$-*Î 178
- Ì$+ZZ2$-4Î 179
- 5.14.3 Copy BC-80X0 180
- Copy Configuration 180
- Ì$+RN2$-SÎ 182
- 6 MESSAGE FORMATTING 183
- POWERSCAN 184
- D8330/M8300 184
- 6.2.1 Cursor Control 185
- 6.2.2 Font Selection 185
- 6.2.3 Clearing Display 185
- 6.2.5 Setting RTC 186
- [Terminator] 187
- 7 TECHNICAL FEATURES 188
- 7.2 POWERSCAN 189
- 7.3 BC-80X0 / C-8000 190
- 7.5 STATUS INDICATORS 191
- 7.6 Reading Tables 194
- HOST CONFIGURATION STRINGS 195
- A HOST CONFIGURATION STRINGS 195
- (100 ms) 197
- PEN (continued) 200
- DATA FORMAT (continued) 202
- POWER SAVE 203
- READING PARAMETERS 203
- CODE SELECTION (continued) 206
- B CODE IDENTIFIER TABLE 209
- C HEX AND NUMERIC TABLE 212
- HEX/NUMERIC BAR CODES 214
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.157 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais